electricLab 4 in 1

Our multi-talented tool for teaching electrical engineering fundamentals

With our electricLab 4 in 1, you can teach the basics of direct current and alternating current technology, electronics and three-phase alternating current. Whether in school, vocational school or in-company training, the electricLab 4 in 1 provides you with optimal support in your everyday training activities.

Teach 4 topics with one product (4 in 1)

We begin with the simplest basic concepts and circuits:

electrical voltage source – switch – consumer. We then move on from Ohm’s law to series and parallel connection of resistors, unloaded and loaded voltage dividers, and bridge circuits. After examining the temperature dependence of resistors and the behaviour of capacitors in direct current circuits, the simplest semiconductor components are discussed. The basic properties of diodes and transistors are demonstrated using examples in direct current circuits.

Experiments:

  • You will get 18 experiments

Alternating current technology is taught based on the basic elements R, C and L. After examining the behaviour in an alternating current circuit, the various series and parallel connections are clearly illustrated using oscillograms and phasor diagrams. Finally, simple filter circuits such as high-pass and low-pass filters are examined.

Experiments:

  • You will get 19 experiments

In the electronics section, the characteristic curves of electronic components are first recorded and evaluated. This is followed by the simplest basic circuits, such as rectifier, stabiliser and amplifier circuits. The last part of the teaching material deals with advanced analogue electronics, in particular the various operational amplifier circuits.

Experiments:

  • You will get 21 experiments

Three-phase alternating current is taught using delta and star connections. The star connection is set up with symmetrical and asymmetrical loads, and measurements of the currents and voltages are taken in each case.

Experiments:

  • You will get 6 experiments

Available in different versions

Available in two versions, the electricLab 4 in 1 offers the right option for every situation.

The electricLab 4 in 1 Training Board complies with DIN A dimensions and can be used in all standard experiment frames or as a tabletop device. This makes it particularly suitable for laboratory teaching. The transparent plastic desk housing allows learners to see inside.

The electricLab 4 in 1 Mobile is powered by a rechargeable battery and can therefore be used anywhere. It offers enough space to store the measuring instruments and laboratory cables, allowing it to be used as a complete mobile laboratory.

Safety

The electricLab 4 in 1 has a number of safety features:

The electricLab 4 in 1 has an electronic short-circuit protection feature. If a short circuit occurs, the electricLab 4 in 1 disconnects the outputs from the power supply.

The laboratory cables and plug-in elements have insulated plug contacts, providing a high level of protection against accidental contact.

The electricLab 4 in 1 is powered by low-voltage safety current (15 V DC), making it ideal for learners.

Didactics

Experiment instructions

The corresponding experiment instructions, covering 300 pages, are available digitally on our learning portal C-LEARNING.

This allows your trainees to learn the basics of the respective topics within four weeks. You can access the C-LEARNING registration page directly via the QR code on the hardware. Once you have registered, you will be redirected to the learning paths for the teaching materials in all available languages. Alternatively, you can search for and open the didactic material via the search function in C-LEARNING. There are different courses for trainers and trainees. While trainees can enter their measurement results and answers in the editable PDF, trainers have access to all the solutions.

E-Learnings

Our E-Learning courses are linked to relevant sections of the content. As a C-LEARNING plus International customer, you can benefit from access to all linked E-Learning courses. If you are not a C-LEARNING plus International customer, selected E-Learning courses are available to you.

Experimental template

The experimental template can be used to work on 63 pre-designed tasks on various topics. The experiments are pre-wired and safe to operate.

Advantages:

  • Only the required sockets are exposed
  • Provides a quick overview
  • Experiments can be set up quickly
  • No time-consuming test experiments or set-up times

The didactic preparation of the experiments enables a functioning circuit diagram. With a universal template, you have the option of designing your own tasks and circuits. The QR code on the experiment sheet gives you quick and easy access to the didactic material.

Whether working individually or in groups, electricLab 4 in 1 allows you to adapt your lessons flexibly. The tasks become more complex as the learning process progresses and the demands on the learners increase.

Do you have any further questions?

We will be happy to advise you on which solution is best suited for your company or educational institution.

Contact us!